Skip to content
IoTronix Solution

SIRIM Certification Cost and Steps for Electronic Products

Published · 8 min read · IoTronix Solution

In short

Does your product have a radio (Wi-Fi, Bluetooth, LoRa, 4G) or connect to a public network? Then it needs MCMC Compliance Approval before you sell it [1][8]. This is also called type approval, and SIRIM QAS International issues it [1][8]. Do you also supply a mains adapter or charger? That part needs a Certificate of Approval (CoA) from Suruhanjaya Tenaga and an ST-SIRIM label [12].

Two regulators, both using SIRIM

"SIRIM certified" can mean two different approvals. The first is for communications equipment under the Malaysian Communications and Multimedia Commission (MCMC). The second is for regulated electrical equipment under Suruhanjaya Tenaga (ST, the Energy Commission). SIRIM QAS International does the certification for both. This is why many owners mix them up [8][13].

Under the Communications and Multimedia (Technical Standards) Regulations 2000, communications equipment must be certified [1]. Regulation 16 bans selling equipment that is not certified, was changed after certification, or has no certification label [1]. The penalty on conviction is a fine of up to RM300,000, up to 3 years in prison, or both [2].

MCMC defines communications equipment as network facilities, customer equipment and radiocommunications equipment, and lists items as small as a wireless mouse [3]. A sensor box with a LoRa radio counts. MCMC appointed SIRIM QAS as its certifying agency. SIRIM QAS certification counts as MCMC approval, so you do not need to apply to MCMC separately [6][8].

Which approval your product needs

A product with a radio or a public network connection needs MCMC approval. A mains adapter or charger needs ST approval. Many products need both [1][12].

ProductMCMC approval via SIRIM QASST Certificate of Approval
Sensor box with LoRa or Wi-Fi, powered 24 V DC from the panelYes: Compliance Approval for the radio product [9][10]Not for the box; yes for any AC to DC adapter you supply [12]
Gateway with a 4G or LTE modemYes: Compliance Approval [9][10]Yes for a supplied adapter or charger [12]
Controller using a pre-approved Bluetooth or Wi-Fi moduleYes: End Product (Host) approval built on the module approval [11]Yes for a supplied adapter [12]
Wired RS-485 or Modbus box, no radio, no public network linkUsually not, as it does not fit MCMC's definitions; confirm with SIRIM QAS [3][11]Not for the box; yes for a supplied adapter [12]
AC to DC adapter, switching power supply or charger sold with the productIts safety and EMC are checked inside the radio product's approval [9]Yes: category 33, Adapter or Charger [12]
Units for R&D, a customer trial or an exhibitionSpecial Approval, not for sale [5]Check with ST before import

ST regulates 34 categories of equipment, mostly household items such as kettles, fans and lamps, plus plugs, switches, cables, adapters and chargers [12]. A 24 V DC controller does not appear in the list, but the adapter that feeds it does. MCMC's short range device code also says an AC adapter used with a radio device must be pre-approved by the relevant regulator [15].

MCMC type approval through SIRIM QAS: the steps

The applicant must be a company registered with SSM in Malaysia [9]. It must be a manufacturer, assembler, importer, network operator or authorised consultant [9]. It appoints a Management Representative, who registers the company on e-ComM, SIRIM QAS's online certification system [9].

  1. Register the test laboratory on e-ComM, unless it is already an Accepted Laboratory [9].
  2. Register the test report: it must come from an Accepted Laboratory, be no older than 5 years and match your model name [9].
  3. Declare your trademark or brand, with MyIPO evidence or an authorisation letter [9].
  4. Submit the Compliance Approval application with fees, then send samples [9].
  5. SIRIM QAS evaluates and issues a Certificate of Conformity (CoC or eCoC) [9].
  6. Get a Self Labelling Program (SLP) ID, print the certification mark, and register each unit's serial number before it goes to market [9].

The approval types include Normal, Parallel, In-house Testing (tested in SIRIM's own lab), Hybrid and Fast Track [9]. Hybrid is for products with a communications module inside. It has three options: Module, End Product (Host) or Complete System approval [11]. Does your design use a module that is already approved? Then the end product approval needs your brochure, user manual, brand declaration, and safety, EMC and SAR reports where needed [11].

Tests, documents and samples

SIRIM QAS checks four kinds of test reports [9]: communication (the radio), electrical safety for the equipment and its power adapter, EMC, and SAR or radiation hazards [9]. For a LoRa or Wi-Fi sensor, the radio test follows MCMC's technical code for short range devices. The device must stay inside the bands set by MCMC [15].

  • Technical specification and colour brochure or photo of the model [9].
  • Original user manual, and technical manual where relevant [9].
  • Full type test report from an Accepted Laboratory [9].
  • Trademark declaration and authentication letter [9].
  • Samples: generally 4 units, one each for certification, communication, safety and EMC [9].

Samples should be new units from production. SIRIM QAS may accept a final prototype if it agrees. Used or R&D samples are rejected [9]. A test report on its own is not a certification and does not let you use the SIRIM mark [14].

ST approval for adapters and mains equipment

Regulation 97 of the Electricity Regulations 1994 covers listed electrical equipment [12]. ST's 2024 guidelines set the steps [12]. First register as a manufacturer or importer through e-DIK to get a Certificate of Registration (CoR), which has no fee [12]. Then apply for the CoA through the e-Permit system [12].

  • Type test report, valid for no more than 5 years from its date and with at least 12 months left when you apply [12].
  • List of components, instruction manual, technical specification and catalogue, and a sample if asked [12].
  • Testing must include Malaysia's national deviations [12].
  • Accepted labs include SIRIM QAS, SAMM accredited labs and IECEE CB Scheme labs, with the CB certificate attached [12].

Equipment approved for manufacture must join SIRIM's Product Certification Scheme and carry the ST-SIRIM label [12]. Imported equipment goes through a consignment test for each batch, or joins the scheme [12]. The scheme starts with a factory check and sample testing. After that, SIRIM checks twice a year. The licence is valid for one year [13].

Official fees and time

SIRIM QAS charges a RM150 processing fee plus an evaluation fee for each test [10]. MCMC says certification takes 5 to 8 working days after the test reports are submitted [7][10].

ItemOfficial figure
SIRIM QAS processing and registration fee (1 year)RM150 [10]
Evaluation fee per radio, e.g. LoRa, Wi-Fi 2.4 GHzRM600 per band [10]
Evaluation fee, BluetoothRM600 [10]
Evaluation fee, safety; EMCRM300 each [10]
End Product (Host) approval with an approved moduleRM450 per application [11]
CoC renewalRM50 per year [9]
ST CoA processing feeRM30 [12]
ST CoA annual fee, single phase; three phaseRM220; RM330 [12]

SIRIM's evaluation fees are for checking test reports, and SST is charged on top [10]. Lab testing is quoted separately, by test method and standard [14]. For time, MCMC says certification normally takes 5 to 8 working days [7]. That counts from a complete application, not from the day you start testing. SIRIM QAS gives no fixed time for its Product Certification Scheme. It says the fastest is 2 months [13].

Who to contact

  • MCMC type approval: Communication and Multimedia Certification Section, SIRIM QAS, Building 25, SIRIM Complex, Shah Alam. Email cmcstech@sirim.my or WhatsApp 019-7172627 [9].
  • SIRIM QAS general line: +603 5544 6000 [8].
  • ST CoR and CoA: e-DIK at edik.st.gov.my, then e-Permit; DagangNet support at 1-300-133-133 [12].

Making a board that needs SIRIM approval?

Tell us what the product does, how it connects and how it is powered. Our hardware team covers requirements, schematic and PCB, firmware, prototype, testing and certification, including SIRIM. Each project is quoted on its own.

Questions

How do I get SIRIM certification for an electronic product?

For a radio or network product, a company registered in Malaysia applies for Compliance Approval on SIRIM QAS's e-ComM system. It submits test reports, documents and samples [9]. For a regulated adapter or charger, register with ST through e-DIK. Then apply for a CoA through e-Permit [12].

How much does SIRIM certification cost?

SIRIM QAS charges a RM150 processing and registration fee, plus evaluation fees [10]. For example, RM600 per band for LoRa or Wi-Fi, and RM300 each for safety and EMC, before SST [10]. Lab testing is quoted separately [14].

How long does SIRIM certification take?

MCMC says certification normally takes 5 to 8 working days [7]. Testing must be done before that. SIRIM's Product Certification Scheme for ST equipment takes at least 2 months [13].

My product uses a module that already has SIRIM approval. Do I still need approval?

Yes. The finished product needs End Product (Host) approval. This uses the module's approval as a base, and checks safety, EMC and SAR where needed [11].

Can you design and certify a board for us?

Yes. Our hardware team designs custom PCBs and firmware, from requirements to testing and certification, including SIRIM. We also do small-batch production from 50 units. Each project is quoted on its own.

Is a SIRIM test report the same as SIRIM certification?

No. SIRIM QAS says a test report is not an approval or certification. It also does not allow you to use the SIRIM mark [14].

Sources

  1. [1]Malaysian Communications and Multimedia Commission (MCMC). Is it mandatory for a communications equipment to be certified before it can be used, offered for sale or sold?
  2. [2]Malaysian Communications and Multimedia Commission (MCMC). Is there any penalty if a person offers for sale, sells or has in his possession with a view to sell any communications equipment which is not certified?
  3. [3]Malaysian Communications and Multimedia Commission (MCMC). What is meant by communications equipment?
  4. [4]Malaysian Communications and Multimedia Commission (MCMC). What is Compliance Approval certification?
  5. [5]Malaysian Communications and Multimedia Commission (MCMC). What is Special Approval certification?
  6. [6]Malaysian Communications and Multimedia Commission (MCMC). Is further approval from MCMC required after the communications equipment has been certified by SIRIM QAS International Sdn. Bhd.?
  7. [7]Malaysian Communications and Multimedia Commission (MCMC). What is the turnaround time of the certification process?
  8. [8]SIRIM QAS International. Communication, Multimedia and Hybrid Product Certification
  9. [9]SIRIM QAS International. Certification Requirement for Compliance Approval (Type Approval) on Communication, Multimedia and Hybrid Equipment (eTAC/DOC/01-1.1, Issue 2 Rev 1)
  10. [10]SIRIM QAS International. Certification Fees (eTAC/DOC/01-2, Issue 2 Rev 2)
  11. [11]SIRIM QAS International. Information Booklet: Hybrid Product Certification, Labelling and Importation (eTAC/DOC/01-3, third edition), 2023-05
  12. [12]Suruhanjaya Tenaga (Energy Commission). Guidelines for the Approval of Electrical Equipment, 2024 Edition (GP/ST/No.37/2024), 2024-06-21
  13. [13]SIRIM QAS International. Product Certification Scheme
  14. [14]SIRIM QAS International. Electrical & Electronics testing services
  15. [15]Malaysian Technical Standards Forum Bhd (MTSFB), registered by MCMC. MCMC MTSFB TC T007:2020 Short Range Devices: Specifications (Second Revision), 2020-05-06