Skip to content
IoTronix Solution

Machine integration · old and new machines

Old and new machines, talking to each other.

IoTronix designs and builds custom gateways, interface boards and firmware so your old machines can share data with your new machines and systems. Machines of every brand and age report to one place: FactoryOS on your phone.

Free site visit · hardware quoted after the visit

OLDRS-485Modbus RTUOLDOmron PLCOLDCAN BusNEWOPC UAMQTTIoTronix
  • Your machines and PLC programs stay as they are.
  • Read-only by default. The gateway does not change machine settings.
  • Any brand, any age, one dashboard.

What we connect

Old controllers and new ones, on one gateway.

If a machine has a data port, our gateway reads it. If it has none, we fit our own sensors and interface board.

  • Modbus RTU/TCPSerial cable or network
  • OPC UANewer machines
  • MQTTSends data to your systems
  • Mitsubishi PLCPLC
  • Siemens PLCPLC
  • Omron PLCPLC
  • Euromap 63/77Injection moulding machines
  • CAN BusEngines and drives
  • RS-485Serial cable
  • LoRaWANLong range radio, no cable
  • Wi-FiNo cable
  • PLC I/OOn and off signals

How it works

Four steps, one team.

  1. Step 1

    Free site visit

    We check each machine, its controller and its ports.

  2. Step 2

    We design the interface

    Gateway, interface board and firmware, made for your mix of machines.

  3. Step 3

    We build and install the gateway

    Our own engineers fit it. Machines run the same way as before.

  4. Step 4

    One dashboard

    Every machine, old and new, on FactoryOS. Data can also go to your ERP by API.

Need one machine to signal another, for example a new line that waits for an old machine? Tell us at the site visit. We design and build that interface, and quote it after the visit.

Proven in client projects

Gateways we built for real machines.

Perfomax

Perfomax · maritime, Singapore

Custom CAN Bus to LoRaWAN gateway

Gets engine data off vessels, where cabling and signal are difficult.

Oriental Nichinan Design Engineering, Teck See Plastic Group

ONDE · injection moulding

Machine condition gateway on RS-485

Designed and built for injection moulding machines with no ready-made connection.

Daikin Malaysia

Daikin Malaysia · HVAC manufacturing

Data collection from an Omron PLC

Machine and conveyor data that sat inside the PLCs, now collected and logged.

FactoryOS

Our own product

The FactoryOS ESP32 gateway

Built for 24/7 factory floors. It connects old machines to FactoryOS.

Scope only. We do not publish client results.

Questions about connecting old and new machines

Can old machines without a PLC connect to new systems?

Yes. We fit our own sensors and an interface board to the machine: cycle count, run and stop, motor current and temperature. The gateway sends this data to FactoryOS, next to the data from your newer machines.

Do we have to replace our PLC or our machines?

No. Your machines and PLC programs stay as they are. The gateway reads the data the controller already holds. It is read-only by default, so it does not change any machine setting.

Can you connect machines from different brands?

Yes. One floor can have Mitsubishi, Siemens and Omron PLCs, Euromap 63/77 injection moulders and machines with no controller at all. Each one connects to our gateway in its own way, and all the data lands in one place.

Can a new machine wait for a signal from an old machine?

Tell us what must happen between the two machines. After a free site visit, we design and build the interface between them and quote the hardware. Until then, we change nothing on your machines.

Can old machine data go to our ERP?

Yes. Once the gateway collects the data, it can be sent to the ERP you already run by API. You keep your ERP and your machines.

What protocols do you support?

Modbus RTU and Modbus TCP, OPC UA, MQTT, Mitsubishi, Siemens and Omron PLCs, Euromap 63 and 77, CAN Bus, LoRaWAN, RS-485, Wi-Fi and PLC I/O. Other suppliers sell this as an IoT gateway, an industrial gateway or a protocol converter. We design and build our own.

Free · 30 minutes

Tell us which machines you want to connect.

Book the free Factory Paperwork Check. We look at your machines on site and quote the hardware after the visit.