Foreign worker levy 2026: multi-tier levy, EPF, automation
Published · 6 min read · IoTronix Solution
In short
Malaysia's multi-tier foreign worker levy was moved to 2026 under the 13th Malaysia Plan. But as of early November 2026, the Government has not published the tier rates. So manufacturers still pay the flat levy. Also, since October 2025 wages, employers pay a 2% EPF contribution for foreign workers. Ministers want factories to use automation so they need fewer foreign workers.
Foreign worker cost in a Malaysian factory used to be simple: levy, permit, medical, insurance, wages. Now three changes make it harder to plan. A multi-tier levy is coming. EPF now applies to foreign workers. And the Government has set a fixed target for how many foreign workers the country should employ. This post sets out what is confirmed, what is still a proposal, and what a plant should do now.
The latest on the multi-tier levy
The Prime Minister announced the multi-tier levy mechanism (MTLM) in Budget 2025. MITI said it would apply from 1 January 2025 to manufacturing and the other covered sectors. Two primary sectors would be exempted. MITI also said the levies collected would go back to industry to fund technology and automation [2]. For manufacturers, MTLM replaces the 80:20 workforce ratio in manufacturing licence conditions. MITI suspended that ratio until MTLM is fully in force [2].
Then the start date was pushed back. The 13th Malaysia Plan moved MTLM to 2026 [1]. In October 2026, The Edge still described the multi-tier levy as a policy due this year, with no rates published [6]. In July 2026, FMM said the current levy is RM1,850. FMM asked the Government for a lower rate for firms where foreign workers are about 10% to 15% of the workforce or less. It also asked for higher levies for firms that use more foreign workers, and for advance notice [3]. That is FMM's proposal. It is not the official tier table.
Who handles foreign worker approvals now
On 1 July 2026, the Cabinet decided to move the foreign worker one-stop centre fully under the Human Resources Ministry, from 6 July [3]. Quota applications now go through the eQuota module of the Foreign Workers Centralised Management System (FWCMS). Manual case-by-case processing has ended [3]. The freeze on new foreign worker quota approvals that began on 18 March 2023 was still in place in November 2025 [5].
The 2% EPF contribution for foreign workers
The Employees Provident Fund (Amendment) Act 2025 was gazetted on 14 May 2025 [4]. From October 2025 wages, employers pay 2% and non-Malaysian employees pay 2% of monthly wages to EPF [4]. Employers must register their non-Malaysian employees. Domestic employees are excluded [4].
| Cost item | Status in November 2026 | Source |
|---|---|---|
| Flat levy (cited by FMM) | RM1,850 per worker | [3] |
| Multi-tier levy | Due in 2026 under 13MP, rates not published | [1] [6] |
| EPF, employer share | 2% of monthly wages from October 2025 wages | [4] |
| EPF, employee share | 2% of monthly wages from October 2025 wages | [4] |
| Minimum wage | RM1,700 now, RM2,000 from June 2027 | [6] |
Why the Government wants fewer foreign workers: the numbers
- Malaysia had 2,132,578 active, registered foreign workers on 15 October 2025, down 13% from 2,452,010 a year earlier [5].
- Manufacturing employed 622,388 of them, the largest group of any sector [5].
- The 13th Malaysia Plan targets foreign workers at 10% of the workforce by 2030 and 5% by 2035 [1].
- Deputy MITI Minister Sim Tze Tzin put current reliance at 13% in October 2026 [7].
What ministers are asking factories to do
On 8 September 2026, MITI Minister Johari Abdul Ghani asked industry to add automation to production as fast as possible. He warned that foreign workers will be harder to get in future [8]. He said employers should identify their dirty, dangerous and difficult (3D) jobs and justify foreign hiring against them [8].
On 2 October 2026, Sim Tze Tzin said Malaysia is far from its target of 3,000 smart factories by 2030, with 93 manufacturers recognised so far [7]. He told manufacturers to go to MITI, MIDF and SIRIM for help [7]. After Budget 2027, Treasury secretary general Johan Mahmood Merican said the Government is open to using part of the levy collection to fund mechanisation [6]. This only means the Government will consider it. It is not a scheme you can apply for.
What a factory should do now
- Calculate what share of your total workers are foreign workers. FMM's proposal and the national target both use this ratio, so any tier will likely depend on it [1] [3].
- Price the full cost per foreign worker: levy, 2% EPF, permit and medical, plus the higher minimum wage from June 2027 [4] [6].
- List the 3D jobs in your factory and the machines each one works on. This is the list MITI says it will ask for [8].
- Pick the two or three stations with the most manual hours and get a baseline before you buy automation, so you can show the result later.
Measure the manual hours before you automate
Book a free 30-minute Factory Paperwork Check. We come to your factory, show you the 3 processes that waste the most time, and reply within 1 working day.
Questions
Has the multi-tier foreign worker levy started?
Not yet. The 13th Malaysia Plan set it for 2026. But as of October 2026, the Government had not announced the tier rates [1] [6].
Do I have to pay EPF for foreign workers?
Yes. Since October 2025 wages, employers contribute 2% and foreign employees contribute 2% of monthly wages. Domestic employees are excluded [4].
Sources
- [1]Free Malaysia Today. Multi-tier levy for foreign workers delayed to 2026, 2025-07-31
- [2]MIDA (republished from NST). MITI: Suspension of foreign worker ratio in manufacturing extended until multi-tier levy is enforced, 2024-12-16
- [3]Federation of Malaysian Manufacturers. FMM urges smooth transition to new foreign worker system, pushes for multi-tier levy mechanism, 2026-07-08
- [4]Skrine. Mandatory 2% EPF Contributions for Foreign Workers to start from October 2025, 2025-06-30
- [5]Malay Mail. Foreign worker numbers in Malaysia fall 13pc to 2.13 million as government steps up efforts to reduce dependence, 2025-11-03
- [6]The Edge Malaysia. Govt willing to consider use of foreign worker levies to fund mechanisation, says Treasury secgen, 2026-10-12
- [7]The Star. Manufacturers urged to start gearing towards automation, 2026-10-03
- [8]New Straits Times. 2027 Budget: Johari urges faster automation, less reliance on foreign workers, 2026-09-08
